当前位置: 首页 - 新闻资讯 - 行业新闻 -

山东通风管道怎么做热处理?

来源: 日期:2019-06-10 发布人:admin

山东通风管道怎么做热处理?
济南通风管道消费的通风设备•●、风管及配件░,依据其所处的环境和保送的气体或粉尘的温度•●、腐蚀性等░,采用防腐资料制造或采取相应的防腐措施。建筑物内的热风采暖•●、通风与空气调理系统的风管布置░,防火阀•●、排烟阀等的设置░,均应契合国度现行有关建筑设计防火标准的请求。
 
  According to the environment and the temperature and corrosiveness of the gas or dust, the ventilation equipment, ducts and accessories consumed by Jinan ventilation pipeline are manufactured with anti-corrosive materials or take corresponding anti-corrosive measures. The arrangement of air pipes, fire valves and smoke exhaust valves in the hot air heating, ventilation and air conditioning systems in buildings should meet the requirements of the current national fire protection standards for architectural design.
 
  A. 通风管道及部件绝热工程
 
  A. Ventilation Pipeline and Component Insulation Engineering
 
 •●、 依据通风管道的断面尺寸和所处的部位肯定绝热固定钉的数量。
 
  The number of adiabatic fixing nails is determined according to the section size and location of the ventilation duct.
 
 •●、 肯定固定钉位置后░,先将通风管道壁上的尘土•●、油垢擦净░,再将粘接剂分别涂抹在通风管道壁面和保温钉的粘接面上░,稍后再将其粘接在一同。固定钉粘牢后应待12~24h后再覆铺绝热资料。
 
  (2) After confirming the location of the fixed nail, dust and grease on the wall of the ventilation pipeline are wiped off, then the adhesive is applied on the wall of the ventilation pipeline and the bonding surface of the insulation nail respectively, and then it is bonded together later. Fixed nails should be adhered to for 12 to 24 hours and then covered with adiabatic data.
 
20130929171556585658.jpg
 
 •●、 绝热资料下料要精确░,套裁下料░,切割面要平齐░,搭接处不要有缝隙。纵横缝错开░,小块资料应尽量用于通风管道上平面中间部位。
 
  (3) Precise cutting of adiabatic material, nesting cutting, smooth cutting surface and no gap in lap. When the longitudinal and transverse joints are staggered, small pieces of data should be used as far as possible in the middle part of the upper plane of the ventilation pipeline.
 
 •●、 明装矩形通风管道绝热应在四角加设镀锌钢板包角░,并用镀锌铁丝固定或打包带卡紧。
 
  (4) Galvanized steel sheet wrapping angle should be added at the four corners of the open rectangular ventilation duct, and fixed or clamped with galvanized iron wire or wrapping belt.
 
 •●、 绝热层外缠玻璃丝布维护层时░,先将玻璃丝布按通风管道断面尺寸的大小裁成幅宽为200~400mm的长条░,并卷成小卷备用。也可依据通风管道断面尺寸的大小•●、直径选用定型加工的不同幅宽的玻璃丝布。缠绕时░,先用“∏”形铁钉固定端头░,然后拉紧玻璃丝布缠绕。边缠绕•●、边整平░,不得有折皱•●、翻边等现象。圈与圈间两边搭接处的搭接宽度普通应为30~50mm。末端一定要用“∏”形铁钉固定░,否则容易松动•●、零落。
 
  _When winding the glass cloth maintenance layer outside the insulation layer, first cut the glass cloth into long strips with a width of 200-400 mm according to the size of the ventilation duct section, and roll it into small rolls for reserve. According to the size and diameter of ventilation duct section, different width glass cloth can also be selected for stereotyping. When winding, first fix the end with a -shaped nail, and then tighten the glass cloth. Edge winding, edge leveling, no wrinkling, flanging and other phenomena. The lap width of the lap between the circle and the two sides of the circle should be 30-50 mm. The end must be fixed with a -shaped nail, otherwise it is easy to loose and fall off.
 
 •●、 玻璃丝布表面面依据设计请求涂刷一道或两道防火涂料░,涂层应紧密•●、平均。
 
  _The surface of glass cloth should be coated with one or two fire-retardant coatings according to the design requirements. The coatings should be close and average.
 
 •●、 室外明露通风管道在保温层外还应加一层镀锌钢板或铝板做维护外壳░,外壳间搭接处采用拉铆固定░,搭接缝用密封胶密封。
 
  _A galvanized steel sheet or aluminium sheet should be added outside the insulation layer to maintain the outdoor exposed ventilation pipeline. The overlap between the shells should be fixed by riveting, and the overlap seam should be sealed with sealant.
上一篇:第一页
下一篇:使用镀锌风管有哪些好处?

推荐产品

  • 厨房排烟
  • 厨房排烟
  • 轴流风机
  • 不锈钢制品

本站图片均由网站所有方提供░,部分图片来源于网络░,如有任何疑问请第一时间与我们联系░,未经沟通本站不承担相关法律责任!

www.w-j-e.com
友情链接:皇都彩票  百盈彩票  光大彩票  皇城彩票  拉菲彩票  1号彩票  金誉彩票  博盈彩票  开心彩票  77彩票  八度彩票  爱购彩票  170彩票  环球彩票  366彩票  聚星彩票  金彩彩票  256彩票  久游彩票  大圣彩票